gsmbxu@ powered by .:DR.APE:.

Your access is limited to certain areas of the board unless you login.By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features.
Registration is fast, simple and absolutely free so please, join our community today!

    Operation Instruction

    Share
    avatar
    DR.APE_GSM
    S founder
    S founder

    Posts : 128
    Join date : 2009-05-19

    Operation Instruction

    Post by DR.APE_GSM on 24.05.09 4:01

    Operation instruction


    (standard unlock procedure for P2K models)

    1. Power on the Smart-Clip and E/G indicator will light green.
    2. Power on the phone without SIM card and flash card (if present).
    3. Connect phone to Smart-Clip and press the "Unlock" button ( red on older clips ).
    4. E/G indicator will light green and go off, the phone will switch off (some models will automatically turn on then).
    5. E/G will light green on success or red on error
    6. Successful unlock resets User Code to 1234, Security Code to 000000


    · Pinout P2K to USB A Standard Cable
    · Pinout P2K to USB A Forced Boot Mode Cable

    Sendo snd2xx/snd3xx/snd5xx/snd6xx/snd8xx unlocking procedure

    1. Power off the phone
    2. Connect clip to the phone using RJ45 cable (pinouts below)
    3. Press UNLOCK button
    4. Press Power button on the phone within 5 seconds after you press UNLOCK button on a clip. RX/TX leds will blink
    5. E/G led will glow green on success.
    When you unlock Sendo phone use either fully charged phone battery OR
    power supply from Smart-Clip. Don't use them both at the same time! If
    you use power supply from Smart-Clip, make sure current is not less
    than 300mA, otherwise not all data will be properly recorded to the
    phone.

    · Pinout Sendo snd2xx snd3xx snd6xx
    · Pinout Sendo snd5xx
    · Pinout Sendo snd8xx


    Unlock procedure for V235 phone with testpoint


    Using "Unlock via Testpoint" function of SmartMoto method


    1. Perform V235 testpoint procedure
    2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab


    Please note:

    During testpoint unlocking procedure phone's LCD must be disconnected.
    Do not use hot air fan to remove a metal shield on PCB. This can seriously damage the handset.
    Use any other alternative tool to cut or drill it. Please make sure you do not damage the board

    Unlock procedure for L2 phone with testpoint

    Using "Unlock via Testpoint" function of SmartMoto method


    1. Perform L2 testpoint procedure
    2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab


    Please note:

    During testpoint unlocking procedure phone's LCD must be disconnected.
    Do not use hot air fan to remove a metal shield on PCB. This can seriously damage the handset.
    Use any other alternative tool to cut or drill it. Please make sure you do not damage the board

    Unlock procedure for M1000

    Models with boot versions up to 0.6.1.2 could be unlocked simply by
    pressing "Unlock" button on Smart-Clip (standard unlock procedure for
    P2K models).

    Boot version 0.6.1.2 needs to be unlocked via Remove RSA option.

    1. Power the phone ON;
    2. Connect the phone to a powered clip;
    3. Launch SmartMoto;
    4. Press Search button in SmartMoto;
    5. Program should detect the handset;
    6. Go to Unlock tab;
    7. Press Remove RSA;
    8. Phone enters boot mode, message "Waiting" appears on the bottom of the screen;
    9. Press 1 and 2 keys simultaneously in upper part of the handset and SmartMoto will continue the process;
    10. Program will show a popup window with de******ion of procedure to follow:
    o Remove phone battery
    o Ensure that USB cable is plugged to the phone
    o Press phone keys 1 and 2 simultaneously
    o While holding Button 1 and Button 2, insert battery
    o Release buttons 1 and 2
    o Message "Waiting" should appear on the bottom of phone’s display
    o Press and release phone keys 1 and 2 simultaneously once more
    o Message "Waiting" should disappear, press 'OK' to continue
    11. SmartMoto finishes removing RSA, the handset turns ON;
    12. Now phone requires being unlocked with Unlock button of Smart-Clip;
    o Connect the phone to the powered clip
    o Press UNLOCK button on the clip
    o Phone reloads. Within 5-10 seconds message "Waiting" appears on the bottom of the phone’s display
    o Press 1 and 2 keys simultaneously in upper part of the handset.
    Message "Waiting" disappears, phone enters boot mode (if you don't
    press these 2 keys during message "Waiting" is displayed, the clip will
    give red E/G led and you will have to start with step 1 again)
    o After 1 and 2 keys have been pressed E/G green led will blink and
    phone reboots. Meanwhile E/G will give frequent green blinking and
    phone will turn on.
    Do not disconnect cell phone from Smart-Clip while green led indicator blinks!
    o Green E/G led glows.
    13. The cell phone is unlocked.


    Models with higher boot version will require Testpoint procedure to be unlocked.


    Please be aware that TP procedure for M1000 and data cable differs from other P2K models.

    Testpoint unlock procedure for M1000

    1. Disassemble the phone;
    2. Connect USB-data cable;
    3. Connect Testpoint A to Testpoint B;
    4. Press Button 1 and Button 2 simultaneously;
    5. While holding Button 1 and Button 2 insert battery;
    6. Release Button 1 and Button 2 for 1 second;
    7. Press and release again Button 1 and Button 2 simultaneously;
    8. Press Search button in SmartMoto;
    9. SmartMoto should detect "S Blank Paragon POG" or "S Blank Rainbow POG";
    10. Disconnect Testpoint;
    11. Go to Unlock tab of SmartMoto.
    12. Select required model from the list;
    13. Press Unlock via Testpoint;
    14. Assemble the handset, it’s ready for use.


    M1000 data cable pinout


    Unlock procedure for V3r phone with testpoint


    Using "Unlock via Testpoint" function of SmartMoto method


    1. Perform V3r testpoint procedure (Please note: temporarily you must choose V3i from a list in SmartMoto)
    2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab


    Please note:
    We strictly recommend to make a backup of flash from any V3i handset
    before performing any procedure. If the process fails to complete you
    will be able to restore your handset to its original state.


    Unlock procedure for V557 phone with testpoint

    Using "Unlock via Testpoint" function of SmartMoto method

    1. Perform V557 testpoint procedure
    2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab


    Unlock procedure for E1070 phone with testpoint


    Using "Unlock via Testpoint" function of SmartMoto method

    1. Perform E1070 testpoint procedure
    2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab

    Unlock procedure for A1000 phone with testpoint

    Using "Unlock via Testpoint" function of SmartMoto method

    1. Disassemble the phone
    2. Connect repair USB cable (pin 13 and 14 shortened)
    3. Connect testpoint A to testpoint B
    4. Connect phone battery
    5. Push Button 1 and Button 2 simultaneously
    6. Press "Search" button in SmartMoto
    7. SmartMoto should find "S Blank Paragon POG", or "S Blank Rainbow POG"
    8. Disconnect testpoint
    9. Open unlock tab in SmartMoto
    10. Select A1000 from phone models list
    11. Press "unlock via testpoint"
    12. The handset is unlocked & ready to be assembled.
    avatar
    DR.APE_GSM
    S founder
    S founder

    Posts : 128
    Join date : 2009-05-19

    Re: Operation Instruction

    Post by DR.APE_GSM on 24.05.09 4:01

    Unlock procedure for E770 and V3x phone with testpoint


    Using "Unlock via Testpoint" function of SmartMoto method

    1. Perform corresponding testpoint procedure
    2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab

    Please remember:
    During testpoint unlocking procedure phone's LCD must be disconnected.
    Do not use hot air fan to remove a metal shield on PCB. This can seriously damage the handset.
    Use any other alternative tool to cut or drill it. Please make sure you do not damage the board.


    Unlocking V3 (boot ver.8.26)

    You need to use SmartMoto to unlock these models.
    1. Power on the phone.
    2. Connect it to PC via smart-clip, detect your phone in SmartMoto.
    3. Go to Unlock bookmark, pick your model, press "Remove RSA" button.
    4. Phone goes into boot mode.
    5. Part of phone firmware is reflashed.
    6. The phone powers on and is ready to be unlocked by Smart-Clip using
    simple "press one button" method (press Unlock button on Smart-Clip).

    Unlocking V1050, V975 (ver R245_xxx) (inc. boot 0.6.1.2) and others models with boot 0.6.3.1


    You need to use SmartMoto to unlock these models.
    1. Power on the phone.
    2. Connect it to PC via smart-clip, detect your phone in SmartMoto.
    3. Go to Unlock bookmark, pick your model, press "Remove RSA" button.
    4. Phone goes into boot mode, reserve copy of security area is created.
    5. Part of phone firmware is reflashed.
    6. Phone doesn't power on after that. SmartMoto will give you the
    message requiring to take phone into boot mode using keys combination:
    *,#, PWR ON (at this moment the phone has to be connected by usb cable)
    or using Repairing cable.
    7. Press "OK" button. Wait till the process ends.
    8. The phone powers on and is ready to be unlocked by Smart-Clip using
    simple "press one button" method (press Unlock button on Smart-Clip).

    V18x/V22x/C65x/C38x/E375/E378i (newer versions), C975/C980/V980/E1000 (Boot Loader 0.6.1.2) unlocking note...

    ..
    Unlocking newer versions of V18x/V22x/C65x/C38x/E375/E378i or
    C975/C980/V980/E1000 (Boot Loader 0.6.1.2) may require additional user
    intervention.
    It may happen that E/G led still blinks after display turns off - it
    means that you have to turn the phone ON manually within 2-3 seconds
    after display turns off; alternatively you can try to unlock this newer
    version of V18x/V22x/C65x/C38x/E375/E378i with battery charger on.


    Unlock procedure for A920/A925/A1000


    1. Power the phone on.
    2. Connect the phone to a powered clip. Phone display should give "USB cable connected" message.
    3. Press UNLOCK button on the clip.
    4. Phone reloads. Within 5-10 seconds phone display gives "Waiting for PST" message.
    5. Press 1 and 2 keys simultaneously in upper part of the handset. The
    phone enters boot mode (if you don't press these 2 keys during "Waiting
    for PST" message, the clip will give red E/G led and you will have to
    start with step 1 again).
    6. After A and B keys have been pressed E/G green led will blink and
    phone reboots. Meanwhile E/G will give frequent green blinking and
    phone will turn on.
    Do not disconnect cell phone from Smart-Clip while green led indicator blinks!
    7. Green E/G led glows. The cell phone is unlocked.

    Axxx/Exxx/Vxxx unlocking note


    Don't unplug cable right after phone reboot, wait until E/G led stops blinking!

    E396/E398 unlocking note

    Remove flash card from phone before unlocking


    C115/C116/C117/C155/C156/E365/V170/V171 unlocking procedure


    1. Power off the phone
    2. Connect clip to the phone using RJ45 cable (pinouts below)
    3. Press UNLOCK button
    4. Press Power button on the phone within 5 seconds after you press UNLOCK button on a clip. RX/TX leds will blink
    5. E/G led will glow green on success *

    * After successful unlock (green led on) phones with inserted sim card may ask for PCK or NCK code. Enter 00000000 ("zero" 8 times)


    · Pinout C115 C116 C117 C155 C156 V170 V171
    · Pinout E365


    Unlock procedure for V3 (RAZR) phone by downgrading boot using testpoint (boot version 8.26)


    1. Perform V3 testpoint procedure
    2. Flash it with V3_boot_7.E.0.smf file.
    3. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.

    Unlock procedure for C975 phone with testpoint (boot versions starting from 6.36)


    Downgrade boot method

    1. Perform C975 testpoint procedure
    2. Flash it with C975_boot_5.F.1.smf file
    3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
    4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.

    Using "Unlock via Testpoint" function of SmartMoto method


    1. Perform C975 testpoint procedure
    2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab

    Unlock procedure for C980 phone with testpoint (boot versions starting from 6.36)


    Downgrade boot method

    1. Perform C980 testpoint procedure
    2. Flash it with C980_boot_5.F.1.smf file
    3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
    4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.

    Using "Unlock via Testpoint" function of SmartMoto method

    1. Perform C980 testpoint procedure
    2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab


    Unlock procedure for E1000 phone with testpoint (boot versions starting from 6.36)

    Downgrade boot method

    1. Perform E1000 testpoint procedure
    2. Flash it with E1000_boot_5.F.1.smf file
    3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
    4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.

    Using "Unlock via Testpoint" function of SmartMoto method

    1. Perform E1000 testpoint procedure
    2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab

    Unlock procedure for V975 phone with testpoint (boot versions starting from 6.36)

    Downgrade boot method

    1. Perform V975 testpoint procedure
    2. Flash it with V975_boot_5.F.1.smf file
    3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
    4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.

    Using "Unlock via Testpoint" function of SmartMoto method

    1. Perform V975 testpoint procedure
    2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab

    Unlock procedure for V980 phone with testpoint (boot versions starting from 6.36)

    Downgrade boot method

    1. Perform V980 testpoint procedure
    2. Flash it with C980_boot_5.F.1.smf file
    3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
    4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.

    Using "Unlock via Testpoint" function of SmartMoto method

    1. Perform V980 testpoint procedure
    2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab

    Unlock procedure for V1050 phone with testpoint (boot versions starting from 6.36)

    Downgrade boot method

    1. Perform V1050 testpoint procedure
    2. Flash it with V1050_boot_5.F.1.smf file
    3. Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
    4. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.

    Using "Unlock via Testpoint" function of SmartMoto method

    1. Perform V1050 testpoint procedure
    2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab

    Unlock procedure for C390 phone with testpoint (boot version 8.26)


    1. Perform C390 testpoint procedure
    2. Flash it with C390_boot_7.d2.smf file.
    3. Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.

    Unlock procedure for V360 phone with testpoint (boot versions starting from 8.A0)

    Using "Unlock via Testpoint" function of SmartMoto method


    1. Perform corresponding testpoint procedure
    2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
    Please note:
    We strictly recommend to make a backup of flash from any V360 handset
    before performing any procedure. If the process fails to complete you
    will be able to restore your handset to its original state.

    Unlock procedure for E1, L6, L7, U6, V190, V191 phone with testpoint


    Using "Unlock via Testpoint" function of SmartMoto method


    1. Perform corresponding testpoint procedure
    2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
    Please note:
    We strictly recommend to make a backup of flash from any E1, L6, L7, U6
    or V190 handset before performing any procedure. If the process fails
    to complete you will be able to restore your handset to its original
    state.

    Unlock procedure for V3i phone with testpoint (boot versions starting from 8.A0)

    Using "Unlock via Testpoint" function of SmartMoto method


    1. Perform V3i testpoint procedure
    2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab


    Please note:
    We strictly recommend to make a backup of flash from any V3i handset
    before performing any procedure. If the process fails to complete you
    will be able to restore your handset to its original state.


    Smart-Clip update procedure



    1. Connect Smart-Clip to PC using LPT cable
    2. Power Smart-Clip ON (warning: don't use battery!)
    3. Go to our Update Zone
    4. Upgrade Zone uses ActiveX element, answer "Yes" to install and run it
    5. Press "Connect"
    6. Press "Update" if your version is out of date
    7. Power Smart-Clip OFF
    8. Disconnect LPT cable


    Note: After the first Smart-Clip update and account registration at www.boot-loader.com
    a new user activates the service within standard price plan. Access is
    provided within one year period since the first Smart-Clip update (date
    of the first update + 1 year). In case if Smart-Clip have not been
    updated before logging to www.Boot-Loader.com , the access will not be valid and user will be asked to perform an update procedure.


    dOwNlOaD hErE

      Current date/time is 11.12.17 10:02